Modular 7ANT RX switch

B I U S link image code list	Show page   Syntax
[<<- Web page|https://remoteqth.com/7ant-rx-switch.php] {TOC} !Quick Start Guide *[How to use this RX antenna switch|https://qro.cz/remoteqth/wiki/index.php?page=Modular+7ANT+RX+switch#How_to_use_this_RX_antenna_switch] *[Single Operator - All bands|https://qro.cz/remoteqth/wiki/index.php?page=Modular+7ANT+RX+switch#Single_Operator_and_All_bands] *[Two independent RX on each band!!!|https://qro.cz/remoteqth/wiki/index.php?page=Modular+7ANT+RX+switch#Two_independent_RX_on_bands] *[Controller|https://qro.cz/remoteqth/wiki/index.php?page=Modular+7ANT+RX+switch#Controller] Single Operator 2 RX (SO2R) / Multi Operator 2 RX - without Bi-Dir beverage This is modular 7 RX antenna switch. It allows you to use up to''' 7 independent RX antennas''' (beverages, Bi-dir beverages, RX loops etc.). You can use just one board for '''single RX output''' or up to '''three boards''' for''' three independent RX''' (on different bands). Unused ANT ports can be open or connected to the dummy load. There is 50 or 75 ohms one and also LC BPF isolation for the splitter or the Bi-dir beverages with two outputs. You can use controller with BPFs and preamp, front end protections and RX way switching. Also two independent RX per band are possible with optional 7 ANT RX SPLITTER. '''This is ideal solution for Single OP through SO2R to Multi-Multi, with up to 2 independent RX per band!''' [https://remoteqth.com/img/ZAW-WIKI/7ant/switch/s5_850.png|noborder] !How to use this RX antenna switch *'''This is almost classic antenna switch with high insulation. What is more complicated there are the dummy loads, which are there for:''' ** Bi-directional (reversible) beverage antenna with both directions output. [link|https://remoteqth.com/two-wire-beverage.php] Allows you to share both direction through bands and RX. ** If you want to use '''TWO INDEPENDENT RX on each band'''. Than you need middle box - '''Splitter'''. [link|https://remoteqth.com/7ant-rx-splitter.php] And it needs right impedance on the ports which are not used. *''' When you use any other antennas and there is no splitter - than you can leave ports open.''' * Have a look here: '''{.redka#id color: #f23f37; font-size: 200%}&#9888;{/} NOTE: TWO coax output beverage antenna works right only, when both ports are loaded with right impedance on the same band. It means that you cannot leave second port open or short! Also if you use first port on 160m and second on 80m than second port have to have load impedance on 160m and first port on 80m. [link|https://remoteqth.com/img/ZAW-WIKI/Bi-Dir_2out/bi_dir_850.png]''' '''{.redka#id color: #f23f37; font-size: 200%}&#9888;{/} NOTE: all outputs are wideband - simply BPFs work only for the dummy loads''' !! '''Schematic and PCB''' [https://remoteqth.com/img/ZAW-WIKI/7ant/switch/sch_lc-850.png|noborder] * [bigger pic|https://remoteqth.com/img/ZAW-WIKI/7ant/switch/pcb-jumper-big.png] [https://remoteqth.com/img/ZAW-WIKI/7ant/switch/pcb-jumper-850.png|noborder] [https://remoteqth.com/img/ZAW-WIKI/7ant/switch/j1_850.png|noborder] [https://remoteqth.com/img/ZAW-WIKI/7ant/switch/j2_850.png|noborder] !Single Operator and All bands *Configuration with one PCB board in the switch [PICTURE|https://remoteqth.com/img/ZAW/7ant/switch/77_2_940.png] *One controller *Up to 7 RX antennas *For most of RX antennas you can leave '''JUMPER LC-R OPEN''' *If you want to use''' Bi-Dir beverage(s)''' with two coax outputs, than switch''' JUMPER LC-R to R and Dummy load to 50 or 75 Ohm.''' *'''EXAMPLE:''' *There is one '''Bi-Dir beverage antenna with two coax output''' connected to '''ANT1''' and '''ANT2''' ports on the switch. If you want to obtain the best parameters of this reversible antenna, than the second port (which is not in use) must be loaded with right impedance (50 or 75 Ohm depends on the design) [schematic pic|https://remoteqth.com/img/ZAW-WIKI/7ant/switch/schema_upraveno_maly-850.png] *The rest ANT ports on the switch are used for another RX antennas like loops, classic single wire beverage etc. '''This ports can stay OPEN. ''' [https://remoteqth.com/img/ZAW-WIKI/7ant/switch/example_single operator-850.png|noborder] *Example of jumper configuration for the Example situation: ** ANT1 and ANT2 has got Jumpers in position R and 50 = Wideband 50 Ohm on this ports when they are unused. [https://remoteqth.com/img/ZAW-WIKI/7ant/switch/j1_850.png|noborder] * [bigger pic|https://remoteqth.com/img/ZAW-WIKI/7ant/switch/a1+2R.jpg] [https://remoteqth.com/img/ZAW-WIKI/7ant/switch/a1+2R-850.jpg|noborder] * SWR for ANT port with jumper configuration: R + 50 ** In our example it is port ANT1 and ANT2 ** When the port is not used, the dummy load is connected (50 or 75 Ohm / 2W with the protections) * [bigger pic|https://remoteqth.com/img/ZAW-WIKI/7ant/switch/R50ohm.png] [https://remoteqth.com/img/ZAW-WIKI/7ant/switch/R50ohm-850.png|noborder] !Single Operator 2 RX (SO2R) / Multi Operator 2 RX - without Bi-Dir beverage *There are two switch PCBs in the box. [PICTURE|https://remoteqth.com/img/ZAW/7ant/switch/IMG_5411_web_2.png] *There is '''NO antenna''' which needs dummy load for the right work. So '''all ports can stay OPEN = Jumpers LC-R are OPEN.''' *'''All OUTPUTs''' are ALL bands so you can use controllers on ALL bands too. '''{.redka#id color: #f23f37; font-size: 200%}&#9888;{/} Do not use controllers on THE SAME band. This is not recommended - use two switches and middle splitter.''' [https://remoteqth.com/img/ZAW-WIKI/7ant/switch/example_so2r mo2r-850.png|noborder] !! '''SO2R / Multi operator 3 RX - without Bi-Dir beverage ''' *There are three switch PCBs in the box. [PICTURE|https://remoteqth.com/img/ZAW/7ant/switch/22_2_940.png] *There is '''NO antenna''' which needs dummy load for the right work. So '''all ports can stay OPEN = Jumpers LC-R are OPEN.''' *'''All OUTPUTs''' are ALL bands so you can use controllers on ALL bands too. '''{.redka#id color: #f23f37; font-size: 200%}&#9888;{/} Do not use controllers on THE SAME band. This is not recommended - use two switches and middle splitter.''' [https://remoteqth.com/img/ZAW-WIKI/7ant/switch/example_so2r mm_all-850.png|noborder] !! '''SO2R / Multi operator - with Bi-Dir beverage ''' * There are three switch PCBs in the box. [PICTURE|https://remoteqth.com/img/ZAW/7ant/switch/22_2_940.png] * Each board must be single band. **First, close to connectors is 160m, middle 80m and top 40m. *'''EXAMPLE:''' *There is '''Bi-Dir beverage two coax output antenna on ANT1 and ANT2'''. This antenna needs dummy load for the right work. So ''' ports ANT1 and ANT2 need Jumpers LC-R to LC and dummy load to 50 or 75 Ohm''' *'''OUTPUTs''' are now '''ONLY single band!''' '''{.redka#id color: #f23f37; font-size: 200%}&#9888;{/} Follow the band lables under connectors outputs on the box.''' [https://remoteqth.com/img/ZAW-WIKI/7ant/switch/example_so2r mm_bands-850.png|noborder] *'''JUMPERS for Bi-Dir antenna''' must be in '''LC and dummy load to 50 or 75 Ohm''' [https://remoteqth.com/img/ZAW-WIKI/7ant/switch/j2_850.png|noborder] '''FIRST board (with 160m LC)''' ----------------------------------- *This is SWR on the''' ANT port which is NOT used'''. Jumpers are configured to: '''LC and 50Ohm.''' ** You can see that the antenna port has got good SWR only on 160m. Rest FQ are on High Impedances... [https://remoteqth.com/img/ZAW-WIKI/7ant/switch/port_ANT1_LC160.png|noborder] '''FIRST (with 160m LC) + SECOND (with 80m LC) + THIRD (with 40m LC) BOARDS TOGETHER''' ----------------------------------- *'''All three boards are connected.''' *Jumper setting is:''' LC + 50Ohm''' *You can see nice SWR on that three bands. *You can imagine it like the antenna is looking into almost 50Ohm impedance. **For Bi-Dir beverage with two coax output it means, that if the antenna port on some band is not used, dummy load is connected and antenna works like it should. [https://remoteqth.com/img/ZAW-WIKI/7ant/switch/port_ANT1_LC.png|noborder] !Two independent RX on bands * '''RX antennas switch for Single / multi op DXing and contesting with TWO INDEPENDENT RX per band.''' * With the [7ANT RX splitter|https://qro.cz/remoteqth/wiki/index.php?page=7ANT+splitter] you can have TWO independent RX on each band! *'''Configuration must be with JUMPERs to LC and dummy load 50 or 75 Ohm on EACH port. [Jumpers |https://remoteqth.com/img/ZAW-WIKI/7ant/switch/j2_850.png]''' *'''Outputs from the switch are only single band - follow the lables on the box.''' *'''All ANT ports on the Splitter have got dummy load impedance on each band (160, 80 and 40m) [SWR on ANT ports |https://remoteqth.com/img/ZAW-WIKI/7ant/switch/port_ANT1_LC.png] ** You can use all antennas include Bi-Dir beverages with the best performance ** There are '''High Power and High Voltage protections!''' [https://remoteqth.com/img/ZAW-WIKI/7ant/switch/s3_850.png|noborder] [https://remoteqth.com/img/ZAW-WIKI/7ant/splitter/splitter_850png.png|noborder] !Controller * Please continue to the [Controller page|https://qro.cz/remoteqth/wiki/index.php?page=7ANT+Controller] [https://remoteqth.com/img/ZAW/7ant/switch/8_2_850.png|noborder]