Status page
This revision is from 2013/03/01 11:38. You can Restore it.
Shows you several major values of server.
- Build number of server software, and status:
- Software up to date.
- Software is old, please update.
- ...after update show return code (done/fail).
- Mishmash - actual build > serverbuild.
- Check new build FAIL.
- Hardware detecton result (based on cpuinfo)
- Actual grayline map with position of sun, use for rotators controll.
- Uptime - Actual time | time server up | connect users | server load
- Disk space - Filesystem | size | use | free | %
- You & server IP | DHCP on/off (1/0)
- Recognized USB devices - list connected device
- CW
- RotX
- ComX
- Rotators config overview
- Ser2Net config overview
- NTP status
RaspberryPI revision
| Rev. No. | Model | Capabilities |
| '0×2' | B1 | Original Model B, 256MB RAM, Ethernet, two USB sockets, five LEDs, (P2) JTAG pins, no mounting holes, Pin3=GPIO0, Pin5=GPIO1, Pin13=GPIO21, I2C-0 |
| ×3 | B1+ | Original Model B with no polyfuses, 256MB RAM, Ethernet, two USB sockets, five LEDs, no mounting holes, Pin3=GPIO0, Pin5=GPIO1, Pin13=GPIO21, I2C-0 |
0×4 B2 Model B, 256MB RAM, Ethernet, two USB sockets, five LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, 12C-1, 8 extra IO pads (P5)
0×5 B2 Model B, 256MB RAM, Ethernet, two USB sockets, five LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, 12C-1, 8 extra IO pads (P5)
0×6 B2 Model B, 256MB RAM, Ethernet, two USB sockets, five LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, 12C-1, 8 extra IO pads (P5)
0×7 A Model A, 256MB RAM, no Ethernet, one USB socket, two LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, I2C-1, 8 extra IO pads (P5)
0×8 A Model A, 256MB RAM, no Ethernet, one USB socket, two LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, I2C-1, 8 extra IO pads (P5)
0×9 A Model A, 256MB RAM, no Ethernet, one USB socket, two LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, I2C-1, 8 extra IO pads (P5)
0xd B2 Rev2 Model B, 512MB RAM, Ethernet, two USB sockets, five LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, 12C-1, 8 extra IO pads (P5)
0xe B2 Rev2 Model B, 512MB RAM, Ethernet, two USB sockets, five LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, 12C-1, 8 extra IO pads (P5)
0xf B2 Rev2 Model B, 512MB RAM, Ethernet, two USB sockets, five LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, 12C-1, 8 extra IO pads (P5)
Update
if shown update button, your can synchonize actual version of software from RemoteQTH.com to your personal server. Only pres this button, and wait for result (displays in red).