Status page

This revision is from 2015/03/17 23:55. You can Restore it.

Shows you several major values of server.

Build number of server software (not system), and status:

Software up to date.
Software is old, please update.

...after update show return code (done/fail).

Mishmash - actual build > serverbuild.
Check new build FAIL.

Hardware detecton result based on cpuinfo (RPI table below)
Actual grayline map with position of sun, use for rotators controll.
Uptime - Actual time | time server up | connect users | server load
Disk space - Filesystem | size | use | free | %
You & server IP | DHCP on/off (1/0)
Recognized USB devices - list connected device

CW
RotX
ComX

Rotators config overview
Ser2Net config overview
NTP status

RaspberryPI revision

cpuinfo rev Code	Model	RAM
0002	Model B Revision 1.0	256MB
0003	Model B Revision 1.0 + ECN0001 (no fuses, D14 removed)	MB
0004-6	Model B Revision 2.0 Mounting holes	MB

Model A

Mounting holes 256MB 0007

0008

0009

Model B Revision 2.0

Mounting holes 512MB 000d

000e

000f

Model B+ 512MB 0010

Compute Module 512MB 0011

Model A+ 256MB 0012

Pi 2 Model B 1GB a01041 (Sony, UK)

a21041 (Embest, China)

Rev. HEX	DEC	Model	Capabilities
0×2	DEC 2	B1	Original Model B, 256MB RAM, Ethernet, two USB sockets, five LEDs, (P2) JTAG pins, no mounting holes, Pin3=GPIO0, Pin5=GPIO1, Pin13=GPIO21, I2C-0
0×3	DEC 3	B1+	Original Model B with no polyfuses, 256MB RAM, Ethernet, two USB sockets, five LEDs, no mounting holes, Pin3=GPIO0, Pin5=GPIO1, Pin13=GPIO21, I2C-0
0×4	DEC 4	B2	Model B, 256MB RAM, Ethernet, two USB sockets, five LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, I2C-1, 8 extra IO pads (P5)
0×5	DEC 5	B2	Model B, 256MB RAM, Ethernet, two USB sockets, five LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, I2C-1, 8 extra IO pads (P5)
0×6	DEC 6	B2	Model B, 256MB RAM, Ethernet, two USB sockets, five LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, I2C-1, 8 extra IO pads (P5)
0×7	DEC 7	A	Model A, 256MB RAM, no Ethernet, one USB socket, two LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, I2C-1, 8 extra IO pads (P5)
0×8	DEC 8	A	Model A, 256MB RAM, no Ethernet, one USB socket, two LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, I2C-1, 8 extra IO pads (P5)
0×9	DEC 9	A	Model A, 256MB RAM, no Ethernet, one USB socket, two LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, I2C-1, 8 extra IO pads (P5)
0xd	DEC 13	B2	Rev2 Model B, 512MB RAM, Ethernet, two USB sockets, five LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, I2C-1, 8 extra IO pads (P5)
0xe	DEC 14	B2	Rev2 Model B, 512MB RAM, Ethernet, two USB sockets, five LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, I2C-1, 8 extra IO pads (P5)
0xf	DEC 15	B2	Rev2 Model B, 512MB RAM, Ethernet, two USB sockets, five LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, I2C-1, 8 extra IO pads (P5)
0x10	DEC 16	B2+	Model B+, 512MB RAM, Ethernet, four USB sockets, two LEDs, mounting holes, Pin3=GPIO1, Pin5=GPIO2, Pin13=GPIO27, I2C-1, 8 extra IO pads (P5)

cat /proc/cmdline | awk -v RS=" " -F= '/boardrev/ { print  }'

Source, 2

Update

if shown update button, your can synchonize actual version of software from RemoteQTH.com to your personal server. Only pres this button, and wait for result (displays in red).

Can force the update by opening sites update.php on server.