Open interface III

Sequencer

Ethernet

Other

• Open *.ino file and find configure section start at line nr 1293
• Uncoment line for enable feature

  #define K3NG_KEYER               // enable CW keyer
  #define BAND_DECODER             // enable Band decoder
  #define FSK_TX                   // enable RTTY keying
  #define FSK_RX                   // enable RTTY decoder

• Modify options

  #define YOUR_CALL "OK1HRA"
  #define MODE_AFTER_POWER_UP 4        // MODE after start up
  #define MENU_AFTER_POWER_UP 7        // MENU after start up
  #define PCB_REV_3_141                // revision of PCB
  #define BUTTON_BEEP                  // Mode button beep enable
  #define CW_TONE 480                  // disable = off, DTR/RTS PC keying
  #define VOLTAGE_MEASURE_ADJUST 0.3   // ofset for precise adjust voltage measure

• Configure Band decoder

  // BAND DECODER Inputs
   #define SERBAUD2     9600     // [baud] CAT Serial port in/out baudrate
   #define ICOM_CIV              // read frequency from CIV (icom_civ.h) ** you must enabled 'CI-V transceive' in TRX settings **
  // #define KENWOOD_PC              // RS232 CAT (kenwood_pc.h)
  // #define YAESU_CAT             // RS232 CAT (yaesu_cat.h) YAESU CAT since 2015 ascii format
  // #define YAESU_CAT_OLD         // Old binary format RS232 CAT (yaesu_cat_old.h) <------- ** tested on FT-817 **
  // #define INPUT_SERIAL          // telnet ascii input - cvs format [band],[freq]\n (serial.h)
  // #define YAESU_BCD             // TTL BCD in A  (yaesu_bcd.h)
  // #define ICOM_ACC              // voltage 0-8V on pin? ACC connector - need calibrate
  
  // BAND DECODER Outputs
   #define SERBAUD3     115200     // [baud] CAT Serial port in/out baudrate
   #define BCD_OUT                 // output 11-14 relay used as Yaesu BCD 
  // #define ICOM_CIV_OUT          // send frequency to CIV ** you must set TRX CIV_ADRESS, and disable ICOM_CIV **
  // #define KENWOOD_PC_OUT        // send frequency to RS232 CAT ** for operation must disable REQUEST **
  // #define YAESU_CAT_OUT         // send frequency to RS232 CAT ** for operation must disable REQUEST **
  // #define REMOTE_RELAY          // TCP/IP remote relay - need install and configure TCP232 module
  // #define SERIAL_echo           // Feedback on serial line in same baudrate, CVS format <[band],[freq]>\n
  
  // BAND DECODER Settings
   #define WATCHDOG                // determines the time, after which the BCD output switch to OFF and Frequency to 0 - uncomment for the enabled <------------------- nefunguje v request modu
   #define REQUEST                 // use TXD output for sending frequency request, if not detect frequency in sniff mode (Kenwood PC, Yaesu CAT, Yaesu CAT old, Icom CIV)
   #define CIV_ADRESS   0x56       // CIV input HEX Icom adress (0x is prefix)
  // #define CIV_ADR_OUT  0x56     // CIV output HEX Icom adress (0x is prefix)
  
  char* ANTname[17] = {            // Name antennas on LCD
      "-",
      "Dipole",     // Band 1
      "Vertical",   // Band 2
      "Yagi",       // Band 3
      "Windom",     // Band 4
      "DeltaLoop",  // Band 5
      "20m Stack",  // Band 6
      "-",  // Band 7
      "-",  // Band 8
      "-",  // Band 9
      "-",  // Band 10
      "-",  // Band 11
      "-",  // Band 12
      "-",  // Band 13
      "-",  // Band 14
      "-",  // Band 15
      "-"  // Band 16
  };

• Frequency to Band rules

  //=====[ Frequency (Hz) to Band rules ]======================================
      //                                        you can expand rules up to 16 BCD Bands
      
           if (freq >=   1810000 && freq <=   2000000 )  {BAND=1;}  // 160m
      else if (freq >=   3500000 && freq <=   3800000 )  {BAND=2;}  //  80m
      else if (freq >=   7000000 && freq <=   7200000 )  {BAND=3;}  //  40m
      else if (freq >=  10100000 && freq <=  10150000 )  {BAND=4;}  //  30m
      else if (freq >=  14000000 && freq <=  14350000 )  {BAND=5;}  //  20m
      else if (freq >=  18068000 && freq <=  18168000 )  {BAND=6;}  //  17m
      else if (freq >=  21000000 && freq <=  21450000 )  {BAND=7;}  //  15m
      else if (freq >=  24890000 && freq <=  24990000 )  {BAND=8;}  //  12m
      else if (freq >=  28000000 && freq <=  29700000 )  {BAND=9;}  //  10m
      else if (freq >=  50000000 && freq <=  52000000 ) {BAND=10;}  //   6m
      else if (freq >= 144000000 && freq <= 146000000 ) {BAND=11;}  //   2m
      else {BAND=0;}                                                // out of range
      //===========================================================================
  

• BCD Output matrix table

      --------------------------------------------------------------------
      Band # to output relay   0   1   2   3   4   5   6   7   8   9  10
      (Yaesu BCD)                 160 80  40  30  20  17  15  12  10  6m
      --------------------------------------------------------------------
                               |   |   |   |   |   |   |   |   |   |   |
                               V   V   V   V   V   V   V   V   V   V   V
                          */ { 0,  1,  0,  1,  0,  1,  0,  1,  0,  1,  0 }, /* --> BCD1
                          */ { 0,  0,  1,  1,  0,  0,  1,  1,  0,  0,  1 }, /* --> BCD2
                          */ { 0,  0,  0,  0,  1,  1,  1,  1,  0,  0,  0 }, /* --> BCD3
                          */ { 0,  0,  0,  0,  0,  0,  0,  0,  1,  1,  1 }, /* --> BCD4
      */};
  

• FSK (RTTY)

  // Serial2FSK (FSK TX)
  #define SERBAUD0  115200         // Serial0 in/out baudrate (seria2fsk, )
  #define AFSK_ENABLE              // AFSK AUDIO (serial2fsk, fsk memory)
  //#define SERIAL_FSK_TX_ECHO     // enable TX echo on serial port
  //#define SHOW_HIDDEN_FSK_CHAR   // show invisible TX characters on LCD
  #define PTTlead  400             // FSK PTT lead delay ms
  #define PTTtail  200             // FSK PTT tail delay ms
  #define MARK     1445            // AFSK mark 1445 / 2295 Hz
  #define SPACE    1275            // AFSK space 1275 / 2125 Hz
  #define FMARK    HIGH            // FSK mark level [LOW/HIGH]
  #define FSPACE   LOW             // FSK space level [LOW/HIGH]
  #define BaudRate 45.45           // RTTY baud rate
  #define StopBit  1.5             // stop bit long
  String FSKmemory[3]= {
    "cq de ok1hra ok1hra k",       // Memory 0 button
    " ok1hra ",                    // Memory 1 button
    " 599 15 "                     // Memory 2 button
  };